Download here: http://gg.gg/vxvi0
I’m writing this down so I can find it later.
The management IP address on my Unifi US-16-XG is wrong. I’m going to change it via a combination of the controller and the CLI. Let’s hope this works.
Hope? Why hope?
Win7 MAC Address Changer is a tool that can change the MAC address of network adapters (wired or WiFi) in Windows 7. It’s usage is straight forward, just select the network adapter (virtual and loopback adapters are not show as it is not need), select your operating system, enter or generate MAC Address and just hit the change button. Download chip genius v 3.00 for free. System Utilities downloads - Chip Genius by Chip Genius and many more programs are available for instant and free download. Ubiquiti may, in its sole and absolute discretion, change the terms of this EULA from time to time, as indicated by the date at the end of this EULA. If You object to any such change, Your sole recourse will be to cease using the Software.
Unifi switches are designed to be managed via the webgui (i.e. their controller).
I’m sure this will also work on my US-48 switch too.Get connected and get in
I’ve done this both via ssh and via the serial port.
You can ssh to your device, using the same credentials you use on your Unifi controller. You’ll see something like this:
If you connect via the serial port, you may have to play around with the baud rate. I suggest you keep increasing it until it works. From my MacBook, this works for me:You’re in!
OK, I’m in. Now, what do I telnet to?
In the above, you can see two items of interest:
*10.0.0.249:22 – the original ssh connection
*127.0.0.1:2222 – my next connection
Here we go:
NOTE: you have to hit ENTER a second time for that Warning and prompt to appear.Configuration mode
Let’s enable the configuration mode.Help!
What to do next?
Ahh! I’ll try network.Network
I changed the IP address (10.125.0.220) and set the gateway (10.125.0.1) like this:
Then I altered the management VLAN:show
Let’s see what we have now:The US-48
The US-48 had lost contact with the controller. I connected via the serial console and entered this command:
Microsoft for mac air download. Then I checked to see what it had:
Good. Checking the controller, the device was connected. There was a ‘STUN Communication Failed’ message. From my reading, that will do way when I reprovision the switch, which I am about to do in order to change the management IP address.
After provisioning completed (which about a minute), info showed:
Now I need to change the management VLAN so it can communicate properly.
Hope this helps.Ubiquiti Mac Address Changer V3 0 Free Download Version 9 0
Download here: http://gg.gg/vxvi0
https://diarynote.indered.space
I’m writing this down so I can find it later.
The management IP address on my Unifi US-16-XG is wrong. I’m going to change it via a combination of the controller and the CLI. Let’s hope this works.
Hope? Why hope?
Win7 MAC Address Changer is a tool that can change the MAC address of network adapters (wired or WiFi) in Windows 7. It’s usage is straight forward, just select the network adapter (virtual and loopback adapters are not show as it is not need), select your operating system, enter or generate MAC Address and just hit the change button. Download chip genius v 3.00 for free. System Utilities downloads - Chip Genius by Chip Genius and many more programs are available for instant and free download. Ubiquiti may, in its sole and absolute discretion, change the terms of this EULA from time to time, as indicated by the date at the end of this EULA. If You object to any such change, Your sole recourse will be to cease using the Software.
Unifi switches are designed to be managed via the webgui (i.e. their controller).
I’m sure this will also work on my US-48 switch too.Get connected and get in
I’ve done this both via ssh and via the serial port.
You can ssh to your device, using the same credentials you use on your Unifi controller. You’ll see something like this:
If you connect via the serial port, you may have to play around with the baud rate. I suggest you keep increasing it until it works. From my MacBook, this works for me:You’re in!
OK, I’m in. Now, what do I telnet to?
In the above, you can see two items of interest:
*10.0.0.249:22 – the original ssh connection
*127.0.0.1:2222 – my next connection
Here we go:
NOTE: you have to hit ENTER a second time for that Warning and prompt to appear.Configuration mode
Let’s enable the configuration mode.Help!
What to do next?
Ahh! I’ll try network.Network
I changed the IP address (10.125.0.220) and set the gateway (10.125.0.1) like this:
Then I altered the management VLAN:show
Let’s see what we have now:The US-48
The US-48 had lost contact with the controller. I connected via the serial console and entered this command:
Microsoft for mac air download. Then I checked to see what it had:
Good. Checking the controller, the device was connected. There was a ‘STUN Communication Failed’ message. From my reading, that will do way when I reprovision the switch, which I am about to do in order to change the management IP address.
After provisioning completed (which about a minute), info showed:
Now I need to change the management VLAN so it can communicate properly.
Hope this helps.Ubiquiti Mac Address Changer V3 0 Free Download Version 9 0
Download here: http://gg.gg/vxvi0
https://diarynote.indered.space
コメント